DIY: How to Build an Industrial Hanging Shelf

If you lot like the look of clean lines and gimmicky shelving merely have an oddly sized space, you tin utilise this tutorial to create your ain custom shelf with a modern-industrial aesthetic. This particular example was used for an electronics shelf hung to a higher place the television; however, you could apply this tutorial for anywhere in your home.

DIY Level: Beginner-Intermediate (The hardest part is non actually building the shelf but installing it.)

Materials Needed:

1 – 1×12 board, cut to desired length (example is 48")*
four – 1-1/2" #6 screw eyes (to screw into shelf)
4 – 3-3/4" #6 screw hooks (to spiral into ceiling)
4 – 3/sixteen" cable/wire rope cutting to desired length (hanging height plus about five" for looping)
eight – 3/16" wire rope clamps
*Optional: one more 1×12 lath, cut to desired length, plus four L brackets, for concealing hanging cords

Note: Shown in the photo above are four long screw eyes for attaching the shelf to the ceiling; however, it is recommended to supplant these with screw hooks.

Stride ane:

Prepare your boards. Sand, paint/stain, or seal.

Footstep 2:

Find studs on ceiling.While your paint/stain is drying on your shelf boards, use a stud finder to locate the studs on your ceiling. Measure and marker where you will insert the four spiral hooks. (In this example with a 48" shelf width, the screw hooks were spaced 39" apart.)

Step 3:

Drill holes in ceiling. Use a v/32 drill fleck to drill holes at your 4 markings.

Pace 4:

Screw four spiral hooks into ceiling.Tip: Utilize a screwdriver through the hook center as leverage to help you screw the hook in toward the stop, when it gets tight.

Step 5:

Adhere four spiral eyes to shelf.Measure and marker where you want your screw eyes on your shelf board. (If possible, these should hang straight beneath the spiral hooks in the ceiling.) Predrill ¾ of the way through the board, then spiral on the screw eyes. Tip: Don't allow the spiral go through the bottom of the board; a protruding spiral tip volition likely be visible when your hanging shelf is mounted.

Step 6:

If attaching a wire-concealing lath, do so now. If not, continue to Pace vii. Use four L brackets, and a few more than screws if yous like the added security, to attach the wire-concealing board to your hanging shelf board.

Step 7:

Adhere a wire clamp to ane stop of each cable/wire rope. Follow instructions on your clamps to create a loop on one end of each of your cables.

Tip: Measure first; salvage plenty cable length for looping the other end in an equally sized loop.

Step eight:

Attach the non-looped side of your four cables to the shelf'south screw eyes. Measure and mark where your second loop should exist clamped.Precision is disquisitional here to create a level hanging shelf.

Tip: This step is catchy to practice alone; have someone assist y'all so your loops are measured and accurate.

Pace nine:

Hang your shelf. Check for plumb. If you need to adjust levelness, screw/unscrew the hook optics in the ceiling as needed.

Enjoy your new, custom hanging shelf! It has a decidedly industrial, contemporary vibe…and keeps things organized to boot.

blackwhantem.blogspot.com

Source: https://www.homedit.com/diy-build-industrial-hanging-shelf/

DIY: How to Build an Industrial Hanging Shelf

DIY Level: Beginner-Intermediate (The hardest part is non actually building the shelf but installing it.)

Materials Needed:

Stride ane:

Footstep 2:

Step 3:

Pace 4:

Step 5:

Step 6:

Step 7:

Step eight:

Pace nine:

0 Response to "DIY: How to Build an Industrial Hanging Shelf"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel